Honda Road

HONDA CRF1000 AFRICA TWIN LOWERING KIT

Fits 2016-20 models and *Adventure Sport Models (available in 50mm Only Option) 

Our Honda Africa Twin lowering kit is designed to lower your motorcycle in two variants in either a – 30mm kit or -50mm kit*.  We have designed and manufactured this complete kit in house here at Krooztune from start to finish.

The main focus on designing this kit was to retain the Front to rear balance of the bike whilst lowering the bike closer to the ground . The common mistake of lowering the bike at one end only results in a bike that is out of balance, hard to steer and greatly affects the handling / chassis characteristics of this Motorcycle. 

*Adventure Sport Models are available in 30mm Only Option 

 BILLET ALLOY LINKAGE

The Rear of this bike is lowered using a Billet Alloy Linkage arm machined from high grade 6061 Alloy. Once fitted this will lower the rear end of your bike by either 30 or 50mm depending on kit selected at time of purchase. Lowering the Front end of this bike needs to be done at a Motorcycle Repair shop or most likely a lot easier if it is performed at a mototrcycle suspension shop.

Our Honda Africa Twin Lowering Kit kit has all the parts and instructions necessary to complete this task easily and most of all accurately and professionally to retain the balance in this Motorcycle. After the bike has been lowered it will need a shorter side stand to retain the correct lean angle once parked.

BILLET SIDESTAND

HONDA CB 500 F/X/R LOWERING KIT

Our Honda CB 500 Lowering Kit Lowers the 2013 thru to 2018 Model Honda CB500 F/X/R Trio in either a 30mm OR 50mm variant.  In the rear we use a high quality replacement CNC Machined linkage arm in both 30mm and 50mm lower options.

The forks require a simple disassemble and installation of our 30mm destrokers and pre load spacers.  We slide the forks up through the triple clamps a further 20mm to match the rear for our 50mm option kit.  (as our destrokers only lower the forks 30mm, sliding forks through the clamps is only needed for the 50mm kit) 

This kit is built to the same High Quality with the same materials that we run on our Australian Championship winning BMWS100RR and Honda CBR1000’s.  

We supply linkage arms to  Factory Level Superbike teams such as ‘Team Honda Australia’ and the ‘Next Generation BMW team ’ bikes here in Australia.  These teams of course demand the best in both fit, performance and quality.  The CB500 linkage is made the exact same way we manufacture these high performance linkages that exceed 280KMPH each weekend! 

In our shop we fit these kits in around 2.5hours.  Any good local MC dealer or workshop will have the ability to fit this kit easily.  Comes with detailed instruction easily followed by yourself or local mechanic. 

KIT INCLUDES 

• Linkage 
• Side stand
• Fork Pre Load spacers
• Fork De-strokers

HONDA CRF1000 Africa Twin Lowering Linkage 

BILLET ALLOY LINKAGE

The Rear of this bike is lowered using a Billet Alloy Linkage arm machined from high grade 6061 Alloy. Once fitted this will lower the rear end of your bike by either 30 or 50mm depending on Linkage selected at time of purchase. 

 Available in 2 options  

-30mm

-50mm

 PARTS INCLUDED IN THE KIT

• Lowering linkage 
• Instructions

BILLET SIDESTAND

Africa twin CRF 1000 billet side stand developed to be shorter in length and obtain correct lean angle to suit our -30mm and -50mm lowering kits.  This stand is manufactured using 6061 high grade Alloy CNC machined here in AUS that simply bolts on and replaces the standard unit.

After lowering the bike the center stand will need custom modification to better suit the lowered bike.  It will work once lowered but it is a little more difficult to operate and to get the bike into the upright center stand position due to the lower bike.  

We provide the instructions to complete these mod’s to the center stand with all our sidestand kits. Very easy to follow step by step instruction. 

HONDA CB 500 F/X/R LOWERING KIT

Our Honda CB 500 Lowering Kit Lowers the 2019 and 2020 Model Honda CB500 F/X/R Trio in either a 30mm OR 50mm variant.  In the rear we use a high quality replacement CNC Machined linkage arm in both 30mm and 50mm lower options.

The forks require a simple disassemble and installation of our 30mm destrokers and pre load spacers.  We slide the forks up through the triple clamps a further 20mm to match the rear for our 50mm option kit.  (as our destrokers only lower the forks 30mm, sliding forks through the clamps is only needed for the 50mm kit) 

This kit is built to the same High Quality with the same materials that we run on our Australian Championship winning BMWS100RR and Honda CBR1000’s.  

Our popular Honda CB500 linkage arm is made the exact same way we manufacture these high performance linkages that exceed 280KMPH each weekend!  

In our shop we fit these kits in around 2.5hours.  Any good local MC dealer or workshop will have the ability to fit this kit easily.  Comes with detailed instruction easily followed by yourself or local mechanic. 

KIT INCLUDES :

• Linkage Arm 
• Alloy Adjustable Side stand
• Fork Pre Load spacers
• Fork De-strokers

LOWERING KIT FEATURES

This Linkage/Fork kit Lowers the 2011-2019 Model Honda CBR250/300 in either 30mm or 50mm at the rear of this bike and 30mm in the front forks using our ‘Krooztune' Lowering kit. The kit comes with a linkage with bearings pre fitted. You will require the standard seals and sleeve out of the Original linkage to fit this part and it basically just bolts in as a replacement over the standard linkage.

The forks require a simple disassemble and installation of our 30mm destrokers and pre load spacers.  We slide the forks up through the triple clamps a further 20mm to match the rear (as our destrokers only lower the forks 30mm). This additional 20mm is only needed for 50mm kit.   

Kit Includes 

• Lowering Linkage
• Shorter Side Stand
• Preload tubes 
• internal fork De-Strokers